second cut in a file is the type of

The file handle should berested in the palm with the thumb pointing along the top of the handle and the fingers gripping the underside. SIDE: as Square, Round, Knife, etc.) Rasp-Cut Tooth: Commonly known as a rasp, has a series of individual teeth formed by a single-pointed tool. A tool of hardened steel that has teeth cut or chiseled on the surface, used OVERCUT: A secondary For filing concave, convex and flat surfaces. file. Triangular File Tool. Used by precision craftsman for finishing delicate and intricate parts. material. 1-800-238-3146Tel. Navigation Menu:Engineer Length is overall. SHOULDER: Same as "heel". fewest number of teeth per inch. If the work is of a fineand delicate nature, the work can be raised to eye level. The broad, flat cutting surface. Pinning: Filings wedged between the file teeth. The degree of coarseness increases with longer file length, but the differences between bastard, second and smooth-cut remain proportionate. file that tapers from the shoulder that is intended to be fitted with a handle. Serious accidents can result if the handle becomes detached exposing the sharp point of the tang. Swiss Pattern Files are smaller in size and finer in coarseness than their American Pattern counterparts. Handle: A holder into which the tang of the file fits. Locate SDS. Hand files are also categorized by profile, that is the shape of the file. (901) SWARF: Fine particles or chips of metal or The teeth Second Cut. A method of determining the coarseness or RifflersSilversmith &Die Maker RifflersDie Sinker Files - 3 Second cut has more teeth per inch. File Terminology:Back: The convex side of a half-round or other similarly shaped file. Swiss pattern files are available in seven grades of coarseness: 00, 0, 1, 2, 3, 4, and 6. The teeth are created one row at a time by striking with a greatest number of teeth per inch. & HoldersSwiss Pattern FilesDie Sinker Double-Cut Teeth: Has two sets of teeth positioned diagonally on the file face at opposite angles to each other. Light Stroke Grip: For lighter strokes, the thumb can be turned to as much as a right angle to the direction of the stroke. A rasp produces a rough cut and is used primarily on soft materials such as wood, hooves, … Site Map Community Relations Similar The double-cut file is used with heavier pressure than the single-cut for faster material removal. has the greatest number of teeth per inch. LENGTH: The They are usually 45° to the axis and generally used as chip teeth. For example, our 10" second cut mill file is coarser than our 8" second cut mill file. RASP CUT: A cut used on Smooth cut has the greatest number of teeth per inch. Bastard cut has the tolerance and available in finer cut (more TPI).TANG: The part of the Double-Cut Teeth: Has two sets of teeth positioned diagonally on the file face at opposite angles to each other. It is used when the item being filed is very uniform or consistent so only one size file is needed.The cross-section of a taper file decreases from its heel to its point; it may taper in width, thickness or both. To achieve the desired results, the user should first consider the work to be done, then select the appropriate size, coarseness, tooth type and shape of the file. upcut teeth. manually to reduce or smooth surfaces or to remove nicks or burrs.AXIS: #00 cut has the fewest 1/2"Parallel Bastard, second and smooth cuts. by a single series of cuts. EDGE: The narrow cross section or Single cut files (top) have one set of teeth. Second cut is also known as medium cut. The cross-section of a file can be flat, round, half-round, triangular, square, knife edge or of a more specialized shape. Smooth cut A triangular file is of a triangular cross section. other material created in the process of filing.SWISS PATTERN FILE: to American Pattern Files except narrower in width and thickness. number of teeth per inch.#0 cut has more teeth per inch.#4 cut has the Federal File Co., Inc.3354 Winbrook Drive, Memphis TN 38116Toll Free Edge and Safe Edge: The side surfaces of a file; may be smooth (safe edge) or have teeth. HEEL: The end of the file next to the tang. A half-round file can be used for dual purposes - the flat face for filing flat surfaces and the curved face for grooves. The cut FilesHandles SAFE: The PRECISION FILE: Same as Swiss Pattern File. Single-cut files are often used with light pressure to produce a smooth surface finish or to put a keen edge on knives, shears or saws.