Any type of guideline for design the Architect can provide will assist the manufacturer in a workable design solution. Manufacturer must be recognized by NAMI. C. Requests for substitutions will be considered in accordance with provision of Section 016000. A. ***Note to Specifier: Verify with manufacturer if internal reinforcing is required based on framing material, size, and configuration. D. Remove from project site, and legally dispose of construction debris associated with this work. ASTM B221/B221M – Standard specification for aluminum and aluminum-alloy extruded bars, rods, wires, profiles, and tubes, 5. B. C. Manufacturer is responsible for all touch-up, repair, or replacement of damaged products during the installation. ***Note to Specifier: Assembly sample provided upon request only. For instance, the design may call for the use of mullion(s) to break up the glass to match the pattern on an existing structure. For stock color AAMA 2604 finishes with 2 coats powder or liquid, provide warranty for color and film integrity for ten (10) years from date of application. A. Do not begin installation until substrates have been properly prepared and approved by manufacturer. F. Install glazing sealants in accordance with manufacturer’s instructions without exception, including surface preparations. D. Installer shall keep area tidy and safe at all times. 3. ***Note to Specifier: Select the appropriate set of test results for the project details. 2. Aluminum – 6063-T52, 6063-T6, or 6061-T6 alloy and temper. Double pane glazing options (verify variances between sloped and vertical glazing as needed. A. Say a given curtain wall is anchored at 12 foot (144 in) floor heights. b. Thermochromic Glass – glazing system that is ‘tinted’ via natural heat. D. Glazing Gaskets – Compression type design, replaceable, EPDM, complying with ASTM C 864, with solid strand cord to prevent shrinkage. ***Note to Specifier: Include a mock-up if the project size and/or scope warrant taking such a precaution. ***Note to Specifier: Consult manufacturer prior to completing this section of the specifications to verify glass solution matches intended application and safety requirements (laminated layers) of product. This section is based on the products of Solar Innovations, Inc., which is located at: 31 Roberts Road Festival of Sacrifice: The Past and Present of the Islamic Holiday of Eid al-Adha. ASTM E283 – Standard test method for structural performance of exterior windows, curtain walls, and doors by uniform static air pressure difference. Pressure of 90.0psf interior = 0.167″ permanent set (overload). 4. Section 033000 – Cast-in-place Concrete – Openings in cast-in-place concrete. ***Note to Specifier: Select one of the following frame finishes and one corresponding color. A. 1. 9. ), 2. Pine Grove, Pennsylvania 17963. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimal results. A. Fabricate components in accordance with the shop drawings approved by the architect. Q. Website: www.solarinnovations.com. ***Note to Specifier: Select warranty below that applies to the selected finish(es). 5 1/2″ (139.7mm), not including glazing depth. ***Note to Specifier: Many code jurisdictions have their own local code requirements. 6″ (152.4mm), not including glazing depth. Include schedule identifying each unit, with marks or numbers referencing drawings, 3. Other alloys and tempers may be used for non-structural members provided they do not void the required warranties. Reinforce components at anchorage and support points, joints, and attachment points for interfacing work. Manufacturer must use an extruded aluminum system comprised of domestically produced aluminum and is fabricated/assembled in the USA. 6. Preparation instructions and recommendations. 12. Parallel to wall deflection should not exceed 75% of glass edge clearance. (1) Basic Mullion and Purlin Design – Uniform bay widths; dimension as recommended by manufacturer. Website: www.solarinnovations.com. Based upon the maximum panel size of 3500mm x. Lubricate using a suitable lubricant compatible with door and frame coatings. Structural Performance – Structural performance as tested in accordance with ASTM-E330; with no glass breakage or permanent damage to fasteners, anchors, hardware, or actuating mechanisms. Restrict deflection to L/360 or 1/8″ maximum. Is the Coronavirus Crisis Increasing America's Drug Overdoses? The following is one example of how a mock-up on a large project might be specified. ASTM E330 – Standard test method for structural performance of exterior windows, curtain walls, and doors by uniform static air pressure difference, 10. c. Solera Glass – Install Solera light diffusion glazing system. Restrict deflection to 1/16″ maximum above doors and/or windows. 1. B. d. Refinish mock-up area as required to produce acceptable work. Curtains and drapery panels come in standard lengths of 63 inches, 84 inches, 95 inches, 108 inches and 120 inches. Aluminum Finish – Two samples, minimum size of 2″ x 3″ (50mm x 75mm), representing actual product and color. C. Provide attachments and shims to permanently fasten system to building structure. 2. 1. Select one of the following options or modify to reflect actual design intents. If you can imagine it, Solar Innovations, Inc. can build it. Section 034500 – Precast Concrete Wall Panels: Opening in precast concrete wall panels. P. Accurately size glazing to fit openings allowing for clearances as set forth by the “Glazing Manual” published by the Flat Glass Marketing Association (FGMA). B. Installer shall protect installed products until completion of the installation from all construction debris and natural elements. Stackwall is an exclusive structural wall system facade glass panels joined. Provide a mock-up for evaluation of surface preparation techniques and application workmanship. Separate dissimilar materials using nonconductive tape, paint, or other material not visible in finished work. Protect installed products until completion of project. Solar Heat Gain Coefficient – Unit to comply with the Solar Heat Gain Coefficient NFRC rated, or simulated in accordance with NFRC 200 protocol, shown in manufacturers latest published data for the glazing and sill specified. Manufacturer must be a member in good standing of the National Sunroom Association (NSA). D. Install all gaskets and tapes at factory, as reasonable. Pressure of 97.5psf positive = 0.275″ permanent set (overload), b. Clean surfaces after fabrication and immediately prior to application of primer in accord with manufacturer’s recommendations. Aluminum and Stainless Steel of type which will not cause electrolytic action or corrosion. 4. We also use third-party cookies that help us analyze and understand how you use this website. Solar Innovations, Inc. strives to produce products tailored to each particular need, residential or commercial. 3. Warranty Addendum – Manufacturer offers extended warranties and service contracts on a per job basis. AAMA611 – Voluntary specifications for anodized architectural aluminum (revised). Remove temporary coverings and protection of adjacent work areas. D. Thoroughly clean all surfaces and substrates prior to installation. Phone 800-618-0669 / Fax: 800-618-0743 ASTM A36/A36M – Standard specification for carbon structural steel, 4. The latest published edition of a reference shall be applicable to this Project unless identified by a specific edition date, B. Consult manufacturer to determine which framing meets project specific requirements. D. Color Samples – Two complete color chip sets representing manufacturer’s full range of stocked colors with a standard size of 2″ x 3″ (50mm x 75mm).